Tersus TSG - Motorcycle Throttle & Grip Kit for Honda Shadows

The Tersus TSG - Motorcycle Throttle & Grip Kit for Honda Shadows from TJ BRUTAL CUSTOMS allows you the opportunity to avoid your motorcycle's cockpit looking like C3-PO's armpit. The Tersus TSG (Throttle and Steering Grip Kit) allows you to eliminate the unnecessary throttle push cable with our Acerus Single Cable Throttle Assembly, and upgrade your motorcycle grips to the "knurley" Malleus Grips all in one kit.  This is an amazing Honda Shadow Bobber Kit!

***If you are looking for a Complete Controls Kit with grips, pegs, shifters and more, while saving some coin, check out our Black Box & Brass Box & Silver Box***

INCLUDES 

• The Malleus Machined Motorcycle Grips
• The Acerus Single Cable Throttle Assembly 

FITMENT:  Fits 1" handlebars
Fits the following models throttle pull cables:
Honda Rebel
Honda Shadow VLX600 / VT600 / Steed 
Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS
Honda Sabre
Honda Magna
Honda VT1100
Honda VTX
*May fit other metric bikes.

BENEFITS

The Malleus Machined Grips

These motorcycle grips are the perfect choice for your Honda Shadow bobber or chopper build! The throttle sleeve tube fits most throttle cables and stock Honda Shadow switch housings and the clutch side grip and throttle sleeve tube will work with all 1" handlebars.

The Tersus TSG - Motorcycle Throttle & Grip Kit for Honda Shadow is the most simple way to set up your handlebars, no need for motorcycle grips that will wear out or need replacing! The throttle sleeve and clutch side grip are machined from 6061 Aluminum and anodized with beautiful knurling, not too extreme, just enough to provide a solid hold!  I always hated when grips were knurled to the point of aggressively shredding my palms!! Not so with the Malleus Grip Set! The throttle sleeve fits perfectly in the Acerus Single Cable Throttle Assembly.

The matching clutch side grip simply slides on and attaches to the handlebar with the included, three, #6-32 set screws. We recommend using a bit of red loc-tite on each screw. 

The throttle sleeve is meant for single cable operation. It is not meant to run the push cable. You do not need the push cable, remove it and enjoy your newfound throttle performance!!  

When installing the Malleus Motorcycle Grips, we recommend using a tiny bit of red thread-locker on the set screws of the clutch side grip. 

The Acerus Single Cable Throttle Assembly

The Acerus single cable throttle assembly for the Honda Shadows is machined from billet aluminum, and made to work seamlessly with the stock Honda Shadow throttle pull cable.  That's right! You do not need to run a push cable!  The stock throttle assembly is quite bulky and lacks any kind of visual aesthetic. Who are we kidding, it's totally haggard! Many folks wish to clean up their bikes cockpit by removing the stock assembly, relocating their switches, (videos HERE) getting rid of the push cable and going to a single pull cable (videos HERE).

Specs:

• Machined from 6061A Aluminum
• Fits 1" handlebars 
• Stainless #8-32 bolts (req. 9/64 allen)
• Threaded for Honda throttle pull cables ONLY

The Acerus allows you to maintain a clean, focused and custom look on your bars with no unnecessary fluff, but enough style to show you have superb taste. because you definitely do, you got-dang champion! 

Fits the following models throttle cables -
Honda Rebel
Honda Shadow VLX600 / VT600
Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS
Honda Sabre
Honda Magna
Honda VT1100
Honda VTX
*May fit other metric bikes.
* Some models stock throttle sleeves may not fit.  

Do not over tighten clamp bolts. Use red loctite on the bolts. Fits 1" bars, will accommodate most grips for 1 inch bars. When clamping the assembly on your bars, a small gap between upper and lower halves is normal, this ensures that the clamp isn't bottomed out before it can adequately clamp the bars. This allows the clamp to work well on raw material bars or bars that have plating or powder coating. When installing on powder coated bars, it may be necessary to use a mallet to tap the halves of the assembly together so the bolts can grab the threads. Powder coating isn't an exact science and the thickness can vary from brand to brand, there is no way to anticipate this and if we made the clamps ID bigger, it wouldn't fit chromed bars.  

We advise using a bit of lubricant inside the throttle assembly and under the throttle sleeve for smooth twist action and prolonged life of the parts.