Straight Up Sissy Bar - Honda Shadow VT600 VLX

$ 109.99 $ 179.99
| /
This Bolt On Sissy Bar for Honda Shadow VT600 VLX 600 motorcycles is a simple and clean design offering an answer for...

This Bolt On Sissy Bar for Honda Shadow VT600 VLX 600 motorcycles is a simple and clean design offering an answer for those in need of a sissy bar, but without the means to make one at home! No welding needed!! 

Bent from 1/2" steel, this is just what you need to strap up a sleeping bag or a drill press!
This Sissy Bar is meant to fit the Honda Shadow VT600 aka VLX600 model in conjunction with the TJBC Curved Bobber Fender, and it will NOT fit a stock fender. We cannot guarantee a perfect fit with other fenders.  
It does not fit the Curved "Short Round" Fender, as doing so would angle your sissy bar to between approximately 10:30 and 11:00 as viewed from the left side of the bike. 

These are cake to install. You can attach them to your axle plates one of two ways: 

TJ's Method - Locate the 3rd & 4th from the rear notch on your axle plate on each side and center punch each plate about 1/2" above the notches. You want to make sure the lower bung doesn't hit the adjustment notches and it doesn't hit the curved portion of the axle plate.  
D
rill a 5/16" hole and then tap it with a 3/8"-16 tap. 

Lay a length of chain over the center line of the tire, tape it down and lay the fender on this, it will give you a perfect fender height! Move your sissy bar to the angle you want and mark the location of the holes on the fender, needed for the bolts to attach to the upper fender supports. Pull the fender off and drill the holes. At the rear of the fender you will want to drill slightly oversized 3/8" holes to attach the Sissy Bar fender supports.

OR

Alternate Method - Drill a 3/8" hole and use a nylock nut on the bolt on the backside of the axle plate. Lay a length of chain over the center line of the tire, tape it down and lay the fender on this, it will give you a perfect fender height! 
Move your sissy bar to the angle you want and mark the location of the holes on the fender, needed for the bolts to attach to the upper fender supports. Pull the fender off and drill the holes. 
At the rear of the fender you will want to drill slightly oversized 3/8" holes to attach the Sissy Bar fender supports.
At the front of the fender we recommend using our Pressio Bolt on Kit! 
We recommend not welding anything to the fender. 
The top of Sissy Bar is approx 15" from the top of the fender. 

Description

Customer Reviews

Based on 6 reviews
100%
(6)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
A
Austin Male
Great looking sissy bar

Took sometime to mount, trying to figure out where I wanted to clock it. Went with the method of drill a hole and taping threads in. Would definitely buy again

D
Daniel
I’m completely pleased with this product.

I’m completely pleased with this product.

D
Darnell Wasnuski
Solid. 5 stars for sure

fit perfect

M
Megan
Easy for a noob

Im a total noob when it comes to this motorcycle stuff i wasnt too sure about how to attac this to my bike, but my partner helped be drill the holes in the bike and the curved fender (love that the fenders and sissy bars are handmade!) and we had the whole thing installed in say maybe 45 minutes. We chose to rattle can the fender and sissy bar and now i get compliments on my little bobber project all the time! #girlswhoride

J
Justin clemens
Perfect fit

I needed a sissy bar on my bike so i could have a place for my pack when i go on camping rides and i have to say, this was really easy to install and its held up to two years of riding and tying tons of stuff to it. Thanks Tj Brutal